Technologies

The dramatic global health emergency due to the SARS-CoV-2 pandemic requires new diagnostic devices capable of identifying the presence of virus particles in patient biological samples. In this direction, the development of an innovative low-cost test, which provides the result within a few minutes, which is reproducible and which can reveal the direct presence of even a few viral particles, would be of fundamental importance for the monitoring and containment of the pandemic.

The compact-GC platform is a MEMS-based analytical module for the purge&trap pre-concentration and (gas)-chromatographic separation of a sample. The two analytical MEMS (pre-concentrator and GC column) are interconnected by means of a MEMS microfluidic manifold. The microfluidic manifold interconnects the analytical MEMS, but it also acts as injector through the integrated micro-valves.

CPIAbot is a conversational assistant supporting the learning of Italian L2 for migrants. It has been tested in particular in the context of CPIA - Centri Provinciali per l'Istruzione degli Adulti - MIUR.

Molecular doping (MD) is a doping method based on the use of liquid solutions. The dopant precursor is in liquid form and the material to be doped is immersed in the solution. During the immersion process, the molecule containing the dopant atom is deposited on the surface of the material forming a self-assembled monolayer, that is, ordered and compact. Through a subsequent heat treatment, the molecule decomposes and the dopant diffuses.

We propose an optical technique for the fast check of the presence, on the exposed surfaces of persons and objects, of explosives and their precursors, or drugs, or in general materials which are not allowed in restricted environments: airports, courts, places of worship, etc. The technique yields bi-dimensional pictures, with exposure time of < 1 sec, reporting the target substances, and their locations and quantities. The technique already provided laboratory preliminary results, to be completed, and fully validated for sensitivity and selectivity.

Detection devices for the presence of molecules of interest (analytes) enjoyed a renewed burst with the introduction of biological components (biosensors). Their high specificity is often used in various fields, from environmental monitoring and biomedicine to the protection and promotion of agri-food products. However, the high cost of production and the lack of compatibility with mass sampling (high-throughput) sometimes limit their use.

The platform allows the deployment of a sensor network with peripheral nodes spread on the crop fields or on the environment for the monitoring of crop parameters/environmental parameters. The network architecture integrated LoRa peripheral nodes for short-medium range communication and star-center NB-IoT based for long range communication. It includes a web server and MySQL database for data storage and visualization. The network architecture is scalable to adapt to the area to monitor.

The platform allows acquisition of data from commercial and custom sensors. By now, the system has been embedded in a wearable wristband where elastomeric based strain gauge have been integrated to detect fine hand/wrist/arm movements. The platform integrates inertial sensors (accelerometers, gyroscopes) to acquire more details about the subject movements. A sensor-fusion algorithm enables advanced movement recognition (gesture, 3D orientation). A machine-learning algorithm is in development to increase the performance of the platform.

The proposed technology deals with the development of active SERS (Surface Enhanced Raman Scattering) substrates ad hoc designed for diagnostics of cultural heritage. The substrates are prepared starting from common commercial 'polishing film' sheets (lapping optical fibers) showing an intrinsic roughness (48- 1000 nm) that favors the SERS effect. A pattern of silver or gold nanoparticles are deposited on these films through Pulsed Laser Deposition (PLD).

The prototype uses soil moisture sensors which, through a measurement of dielectric permittivity, estimate the soil moisture based on which irrigation is started through relay-controlled solenoid valve. The system was developed using Open Source technologies. Specifically, for the hardware components, a small sized board computer Raspberry PI 3B + was used together with a 4G LTE Wi-Fi router and a Modbus rs485 / USB converter.

The Q-PLL is a nonlinear circuit which can maintain a locked state when forced by two incommensurate frequencies.

The locked state is a third frequency parametrically selected among those prescribed by the theory of three-frequency resonances in dynamical systems.

In particular, the locked frequency forms a three-frequency resonance with the frequencies of the quasi- periodic input and is closely related to the pitch perception of complex sound in humans.

AIS aim is a robotized inclinometer measurement in standard inclinometer boreholes. The deep measurements have multiple applications, including: evaluating the rate of deep-seated ground deformation in landslide areas, evaluating the volume of deep-seated landslides and assessing landslide hazards. The AIS is composed by an electronic control manager, an inclinometer probe and an electric motor equipped with a high precision encoder for handling and continuous control of the probe in the borehole.

Network structures that require the use of a common database are affected by the risk of processing identification data that are necessary for sharing information and updating and processing data with equal access level between the network nodes. However, this sharing could lead risks of vulnerability when identification data are exchanged between the nodes of the network. The proposed information system involves the exchange of information by encrypting the identification data with an MD5 Hashing procedure (RFC1321).

This technology is based on an algorithm able to provide the probability of being asthmatic with high accuracy. This probability is based on the evaluation of respiratory function and, specifically, of forced expiratory vital capacity in the first second (FEV₁), in resting conditions, and 20 minutes after administration of a bronchodilator drug.

IMM has developed tactile sensors for the detection of objects and surface and for the handling of objects with humanoid robots (e-skin). These devices can be integrated on ultra-flexible and high conformable substrates and they can be used for multiple applications: 1) for a correct interaction with objects distributed in complex environment; 2) for a safe short-range interaction between humanoid robot and humans; 3) for fabricating smart wearables for the detection of biometric parameters (e.g. heartbeat); 4) for remotely control rovers with wearable gadgets.